Pretty Lights After Party, Fluid510: speaker placement
Public v11, 2026-11-20. DJ on the bar (west) side, two stacks in front of the stage firing east, a spacer under each DS210 top, one dance zone. Interactive 3D: model.html. PDF: guide.pdf. Cabling plan: cabling-plan.pdf. All files.
ESTIMATES: the space is 25 x 20 ft. Tech booth (about 4.8 x 3.9 ft, north-west corner), 5.6 ft stage and 6 x 2.5 ft DJ table are scaled or assumed. ASSUMPTION: the house rack and amps are in the tech booth and stay there (not confirmed). Ceiling about 21 ft (not checked). Measure at load-in.
TL;DR
From the bar side (west): stage + DJ facing east, then two stacks on the floor (each 2 IB218 + F315 + spacer + DS210), all firing east.
Spacer under each DS210 (between F315 and DS210): ASSUMED 4 in (10 cm) block, full DS210 footprint; real size not known yet. DS210 centre 6.0 ft, aimed 2.0 deg down.
Stack 7.1 ft, about 330 kg: strap each stack (tips at 21 deg, about 55 kgf push at the top), castors off, non-slip spacer.
One zone: everything from 5 ft in front of the stacks to the east edge is dance floor, about 230 sq ft.
House rack and amps stay where they are (tech booth, assumed). Runs: north stack 3x 5 m NL4, south stack 3x 10 m NL4, 2x 2 m IB jumpers, 4x 10 m XLR.
Subs to F315 crossover around 60 Hz, set in the processor; no box moves. Check it at soundcheck (below).
Notes for the sound engineer
60 Hz is low for the F315. Maker figures: F315 usable 60-250 Hz at -3 dB, crossover band 85-220/250 Hz; IB218 usable 25-80 Hz. Expect a soft spot around 60-85 Hz; if the kick sounds thin, try 80 Hz.
Time alignment: fronts are flush, so the geometry difference is tiny: the F315 arrives 0.4 ms before the IBs at the mix spot (1.0 ms at the front of the floor). Check polarity and delay at the mix spot with a measurement mic.
House rack not confirmed. If it is somewhere else, the cable lengths change.
The stage covers the front of the left bar (y 0-12.8 ft). FOH in the booth hears the rig from the side: check the mix on the floor.
Plan and side view
Stage / DJ riser: x 0-5.6 ft along the bar side, south of the booth. The DJ faces east.
Spacer: 4 in (assumed) between F315 and DS210, fronts flush.
Stack N: 1-6.1 ft from the north wall, next to the booth. Stack S: 13.9-19 ft. Box backs at the stage edge, fronts flush at 8.4 ft.
DS210: centre 6.0 ft up (just above head height), aimed 2.0 deg down, toed in 21 deg. 100% of the floor is in both beams.
3D view
Speakers drawn as plain boxes at true outer size. Interactive: model.html.
Cable runs from the house rack
Rack in the tech booth (assumed). Route: out of the booth's south side, along the stage front edge behind the stacks (taped), into the back of each box. Needed = path + 2 m for drops and slack + 15%.
Run
Type
Needed
Take
Note
IB pair N
NL4
3.7 m
5 m
home run to the bottom IB, 4-core jumper to the one above
F315 N
NL4
4.0 m
5 m
DS210 N
NL4
3.9 m
5 m
one NL4: mid on 1+/1-, HF on 2+/2-
IB pair S
NL4
8.3 m
10 m
home run to the bottom IB, 4-core jumper to the one above
F315 S
NL4
8.5 m
10 m
DS210 S
NL4
8.4 m
10 m
one NL4: mid on 1+/1-, HF on 2+/2-
DJM-A9 Master 1 L/R -> WING Rack ch 1/2
XLR x2
6.3 m
10 m
DJ feed (only the monitors come from the S32)
S32 -> booth monitors (K12.2)
XLR x2
6.3 m
10 m
monitors on the DJ table ends
AES-50 console to stage box
Cat5e
1-3 m
short patch
both in the booth
Total: 3x 5 m + 3x 10 m NL4 (+2 spare), 2x 2 m IB jumpers, 4x 10 m XLR. Each IB pair is 2 ohm on one amp channel; loss on 10 m of 4 mm2 about 0.4 dB.
Details
Speakers: IB218, F315, DS210 (Funktion-One). Box sizes and coverage from the maker's drawings and data sheets.
Coverage: DS210 100 x 25 deg, 0.5 ft grid at ear height 5.6 ft.
Time alignment: acoustic centres at the middle of each box, fronts flush, ears 5.6 ft; speed of sound 1130 ft/s.
Changelog: public v11, 2026-11-20, requested by the organiser: placement v11 (v10 + spacers under the DS210 tops), plain boxes instead of maker 3D models.